• Plastic
• Foam
• Wood
• Circuit Board
• Light Aluminum
• Brass

• We use ABBA or THK LM Rail guides.
• Proven Reliability providing less down time.
• Supreme customer service, pre and post sales.
• Fully assemebled and tested machines.
• Affordable prices.
• Made in Anaheim CA.
• We designed and manufacture in Anaheim CA USA.
• Availible machine designers ready to speak to you.

• Footprint (overall size not including motors): 120" x 64" x 26".
  (feature many change at any time.)

• Footprint with the motors 120" x 78" x 26".
  (feature many change at any time.)

• Y-98"
• Y-50"
• Z-5" or 8"

• Structure is CNC machined 6061 aluminum and precesion extrusions.
• 6061 Billet Machined Aluminum
• Standard X and Y Axis uses 20mm ABBA Brand linear rails/blocks (4 Blocks for X and 2 for Y). Read more about ABBA rails click here.
• Upgrade only X and Y Axis uses 20mm THK Brand linear rails/blocks (4 Blocks for X and 2 for Y). Must be stated in the formal Quote.

• Linear Hardened Shaft Guides
• Linear Bearings Blocks (ABBA) with grease inlet. Read more about ABBA rails click here.
• Precesion Rolled Ballscrews .001" Backlash.
  • Resolution .0001"
  • recirculating ball nut with grease inlet.
• Belt Drive geared down for power and accuracy.
• 5" Travel Standard.
• Upgrade only X and Y Axis uses 20mm THK Brand linear rails/blocks. Must be stated in the formal Quote. Now available
• Colombo and HSpindles require upgrades to include additional blocks and longer rails on Y Axis (24")
• Smooth linear motion vs bearing contact on V shaped steal bars.
• Custom feed rate is availbie upon request. Please call us and ask for Kevin.
• 5" Travel, comes with Rigid Rails and Ballscrew of .001 inch backlash tolerance, Clearance of 5" (Recommended).
• 8" Travel, comes with Rigid Rails and Ballscrew of .001 inch backlash tolerance, Clearance of 8".
• 12" Travel, comes with Rigid Rails and Ballscrew of .001 inch backlash tolerance, Clearance of 12".

• INCHES	METRIC
  DECIMAL	mm
  .00025"	.00635mm
  .00050"	.0127mm
  .001"	.0254mm
  .003"	.0762mm
  .006"	.1524mm

  available

• X and Y axis are Rack and Pinion
• Linear Bearings Blocks (ABBA) with grease inlet. Read more about ABBA rails click here.
• Y axis has dual motors ( Each side has a motor and a gear rack).
• Tolerance of .006
• Repeatability of .006
• Rapid Traverse is 800 inches per minute.
• Feed Rate recommended 150 - 200 inches per minute.
• Custom feed rate is availbie upon request. Please call us and ask for Kevin.
• Gear ratio is 4:1 (belt drive reduction)
• Rack-n-pinion Gear material is steel.
• Smooth linear motion vs bearing contact on V shaped steal bars.

• Low Maintenenace.
• Very similar if not the same as most automation system that run 24 hours a day!
• Accurate Cutting
• Heavy load capacity
• Sealed bearing blocks.
• presecion grounded
• wippers on both ends.
• High rigidity many contact points
• Low axis motion noise
• High durability
• Low maintenance
• Smooth linear motion vs bearing contact on V shaped steal bars.

• Currently Not availibe.

• Ratio is 2:1 on Z.
• Ratio is 16/48 on X and Y
• Pulley made of Aluminum.
• Belt has reinforces fiber.

• Window XP or 2000 or Vista
• Processor (1.00GHz) or greater.
• Memory
  256MB DDR SDRAM at
• Hard Drive 20GB
• USB
• Parallel port on mother board or PCI slot.
• All background software to be removed from computer.

• CD, Manual, Hard Key
• Support from VisualMill
• Support from Rhino CAM
• Mach 2 and CAM soft must be on separate computers.
• No print instructions or manual thru K2

• Mach 3 CD or download from Mach 3 site.
• Set Up is from K2 CNC
• Support from Mach 3
• Mach 3 and CAM software must be on separate computers.
• Basic print instructions or manual thru K2
• Mach 3's Manual will be on a CD in PDF format.
• K2 machine settings will be provided.

Computer REquirements:

• Window XP or 2000
• Processor (1.00GHz) or greater.
• Memory
  256MB DDR SDRAM at
• Hard Drive 20GB
• USB
• Parellell port on mother board or PCI slot.
• All background software to be removed from computer

• Rhino CAD
• ArtCam Pro
• ArtCam Insignia
• KCDW
• Profile Lab
• To see more click here.
• Most any CAD software will work

• CD, Manual, Hard Key
• Support from VisualMill
• Support from Rhino CAM
• Mach 2 and CAM soft must be on separate computers.
• No print instructions or manual thru K2

• Rhino CAM
• VisualMill
• ArtCam
• ArtCam Insignia
• Profile Lab
• To see more click here.
• Any Cam program will work with this machine as long as it postprocces to G-code or fanuc

• Used for Homing, Zeroing X, Y and Z
• Accurate.
• Pre-Wired
• Requires the purchase of Controller with limit switch option and programming in control software
• Made of micro switches

• Rotozip
• Porter Cable 690LR or 892 router (should fit most routers with 3.5" round body)
• Porter Cable PC-7518 router 4.20inches in diameter.
• Bosch - 1617 motor (3.5in diameter)
• Hitachi (3.27 in diameter). Mount is available
• Makita (3.22 in diameter). Mount is available
• HSD spindle
• Colombo Spindle

• Porter Cable (690LR or 892 router (should fit most routers with 3.5" round body)
• Porter Cable PC-7518
• Hitachi (3.27 in diameter) - Not sold through K2
• Makita (3.22 in diameter) - Not sold through K2

• Quite
• Longer Lasteing
• .00025 inch runout.
• 220 V
• 1 or 3 Phase
• ER25 Collet
• Out start with Mach2 or Mach3.
• K2 Adds more bearing and lenght to the machine.
• Rating of HP is confrim and back by maker. The power of an industrial spindle is very noticable when doing actually cuts vs that of regular routs with same HP rating.
• 1 year warranty
• Starts at $3400.00.

• INCHES	METRIC
  DECIMAL	mm
  .00025"	.00635mm
  .00050"	.0127mm
  .001"	.0254mm
  .003"	.0762mm
  .006"	.1524mm

• Aluminum Table top custum extruded with T-slots for 1/4-20 slots
• 0.500 inch thick.
• 6061 aluminum
• Every 3 inches. (feature many change at any time.)

• 4 Servo Motors with feedback encoders.
• Geckodrive G320 servo controller
• Wired for Step/Dir signals from Printer/Parallel Port
• Fully enclosed control box and prewired for Parallel Interface
• 110 (std.) or 220 (request) watts power supply. 24VDC unregulated (~30V) 8 Amps.
• 5 watt power input wire from 1 computer USB port.
• Enable button
• Power Cord
• Fuse
• No - Router E-Stop or remote off switch.
• Mach 2 Controller software CD with purchase or download demo from Mach 2 site.
• Mach 2 Set Up is from K2 CNC with purchase
• Support is from Mach 2 via email
• Parallel Printer Cable for controls (Currently No USB)
• USB for additional 5W Power Only
• International Power Cord for 220 VAC (Please request)
• 4 Servo Motors with feedback 1000 line US made encoders.
• Z uses 305 oz/in. 60W, 24VDC, 2800 max RPM, 3.5A, Close loop.
• X uses 350 oz/in. 120W, 24VDC, 3000 max RPM, 8.5 A, Close loop.
• Y bottom 98 movement uses (2) 350 oz/in. One per side of the frame in tandem. 120W, 24VDC, 3000 max RPM, 8.5 A, Close loop.
• Geckodrive Servo Controller.
• Wired for Step/Dir signals from Printer Port.
• Uses CAT 5 Plugs for encoders.
• Fully enclosed control box and pre-wired for Parallel Interface.
• Support is from Mach 2 via email or by phone.
• Mach 2/3 has a maximum of 4 axis control.

• 2 Servo Motors DC  for Y
• 1 Servo Motors for X axis
• Strength - 305 oz/in torque
• Stronger than typical Steppers
• US Brand encoder
• All K2 Servos are Close Loop (FeedBack to the controller)
• 1000 count per revolution.

• 1 Servo Motor DC  Z axis
• Strength - 305 oz/in torque (NEW)
• Stronger than typical Steppers
• US Brand encoder
• All K2 Servos are Close Loop (FeedBack to the controller)
• 1000 count per revolution.

• Black allowance for motor wires, limit switches and encoder wires.
• Keeps the wire looking clean and out of the way.
• Location of X and Y axis only.
• Easy access and installation of additional power wire and other wires. There is a break in the plastic. Ask a rep for details.

• 200 to 370 CFM.
• 5 to 15 HP
• Availible with table or without.
• 1 to 3 phase power requirements.
• 230 - 340V.

• Welded mild steel (3 x 3 square tubing) Specs may vary.
• Painted Gray.
• Adjustments on feet

• Collects dust and small chips.
• Fits 2.25" diameter hose.
• Vacuum and Hoses are NOT included
• Collects approximately 80% of cut debris

• Email (Unlimited)
• Phone (Limited to set up and assembly of machine and controller)
• Phone (basic operation of the machine. Not to include CAM programming)
• Controller support (Email from Mach2)
• CAD/CAM Support (Email, Phone, Fax from Appropriate vender)
• On site support is available at an additional charge.

• Requires Palette Delivery
• Typical Company: UPS (United Parcel Services) Residential or Business. Delivery to the door.
• Palette is made of 1/2 thick ply wood and 2x4.
• $35 more for residence delivery
• Will need more than one person to carry from truck.
• Total weight approximate 190 LBS. May vary depends on options.
• Shipping outside the US may need to have a different carrier and method.
• International Shipping is available

• Estimated time of 1- 2 hours.
• Wires pre-installed.

• 12 Month on all parts that are defective
• This does not cover dust, water, or user damage

• 15 days to return machine. Motors and controller can be used but not damaged. 100% Money Back on machine, motors, and controller less shipping and handling. Customer pays to return ship.

• Computer
• Vacuum Table -
• A vise or Fixture to hold part -
• Your Cutting Program - Not available thru K2
• Cutting Tool (End Mill or Drill Bit) -