New KT-2514-06 (Shaft linear motion, steppers -upgrade to servo optional)

This small but yet rigid machine can cut in aluminum given the proper conditions. You can use this machine to cut inlays for guitars. With the right software you can repeat accurate circle cutting. Use high speed steal to carbide endmill. The aluminum table to offers rigid foundation while the T-sloted areas allow easy fixturing of your parts. The machine comes standard with cable carriers and limit switches. Quality is important and that's why we machine almost all aluminum parts in-house. From CAD, CAM to assembly; we do it all, in-house to provide you with a quality desk top CNC router that will provide you an accuracy, repeatability, rapid cutting.

New KT-2514-06
New features:

• Folddown shipping position.
• Easy to assemble. 95% preassembled.
• Wider Bottom bearing arrangement.
• All Axis Kert Lead screws and Kert Nuts.
• Standard High Torque stepper on Z axis.
• Rubber feets

CLICK TO ENLARGE

MDF, Maple, Balsa, Corian, Circuit Board, Hard Wood, Plastic.

3 inch of Aluminum. Special misting, tools, proper feed rate, and knowledge of cutting aluminum required.

Read our frequently asked question page. Click Here

CLICK TO ENLARGE

Z Axis.
Type: Steppers.
Includes a turn knob.
Stronger steppers on the Z axis provide plugging power.

Nema 23 size motor mounts on all axes.

160 Oz/in torque. Standard.

280 Oz/in torque. Upgrade.

X and Y Axis
Type: Steppers

Nema 23 size motor mounts on all axes

160 Oz/in torque. Standard.

280 Oz/in torque. Upgrade.

-Travel: X-25" Y-14" Z-2.75"
-Upgradeable to Travel: Z: 4.75"

- Footprint (overall size not including motors): 31" x 16" x 16"

- Table top size: 30" x 15.5"

CLICK TO ENLARGE

KERK Brand Anti-Backlash Nuts on all axis

-0.1 pitch lead screws. Standard (Feed rate of 150 inch per minute)
-Kerk(TM) Nut

Backlash: 0.0005 inch

Resolution: 0.00005 inch

Direct drive coupling /w 2000 full steps/in. (on 1.8 degree stepper)

-Made of 6061 Aluminum and Delrin.
-Now anodized black.

4 linear ball bearings on each axes
Now with wider arrangements.

Harden precision shafts

X - 20mm

Y - 16mm

Z - 16mm

CLICK TO ENLARGE

Spindles that are availble thru K2
Click here for more info on routers.

• PC 7310
• PC 892 - Max .50 inch endmills. (Recommended)

Mounts that are availible thru K2.

• PC 7310 Trimmer
• PC 892 - Max .50 inch endmills. (Recommended on this machine)
• Ryobi
• RotoZip
• Kress
• Dremel 300

-On X and Y Axis.
-The cable carriers have one side that allowes easy access to removing and installing additional wires like router cord.

Stepper Controller Standard 3 Axis Standard.
Servo is an upgrade option.

3 to 4 Servo Motors with feedback encoders.
Gecko Drives - Wired for Step/Dir signals from Printer/Parallel Port -
Fully enclosed control box and pre wired for Parallel Interface
110 (std.) or 220 (request) watts power supply. 24VDC unregulated (~30V) 8 Amps.
5 watt power input wire from 1 computer USB port.
Enable button - Power Cord - Fuse - (E-Stop or remote off switch. )
Works with Mach 2 or Mach 3 Controller software.

CLICK TO ENLARGE

Endmills and cutting bits.

.5 HSS inch diameter availible (will only fit appropriate routers)

.25 HSS inch diameter availible (will only fit appropriate routers)

8th inch bit holder. Brass adapter. (.500" diameter shaft) Made By K2 CNC.
Used with your Porter Cable 892, 690, 7518 Router.
Will Not work with Porter Cable 7310 trimmer, Kress , and Bosch Colt Router.

Buy now.

8th inch bit holder. Brass adapter. (.500" diameter shaft) Made By K2 CNC.
Used with your Porter Cable 892, 690, 7518 Router.
Will Not work with Porter Cable 7310 trimmer, Kress , and Bosch Colt Router.

Buy now.